Oztec Concrete Vibrators, Ceiling Grinders

Oztec Concrete Vibrators was formed in 1965. Oztec Industries began building their reputation as a designer and manufacturer of quality construction equipment. Oztec's line of fully interchangeable concrete vibrator steel and rubber heads,along withg electric and gasoline motors, back packs and portable mounts and flexible shafts are the most powerful, versatile and reliable in the industry. Oztec concrete ceiling grinders are one of the best in the industry.

Popularity
Set Descending Direction

Grid List

30 per page

Items 1 to 30 of 31 total

Page:
  1. 1
  2. 2
  1. OZTEC 1.2 HP Electric Concrete Vibrator 1.2-OZ

    Starting At $549.00
    The OZTEC 1.2 HP Electric Concrete Vibrator 1.2-OZ motors are manufactured to exacting specifications to withstand the rough day to day abuses associated with construction sites. Lightweight compact and fitted with our comfortable adjustable shoulder strap this one man power unit will speed through the stiffest concrete. Using the Vibrator Selection Chart allows you to combine power units with any of Oztec's steel or rubber vibrator heads for maximum productivity. Learn More
    loading
  2. OZTEC BP-45A 4-Stroke Gas Backpack Concrete Vibrator

    Starting At $1,643.00
    The OZTEC BP-45A 4-Stroke Gas Backpack Concrete Vibrator is powerful portable and reliable. Oztec gas power units provide ultimate and immediate adaptability on the job. Utilizing rugged and dependable Honda gasoline engines coupled to our "speed-up" transmission vibrator heads develop 12000 vpm and never drop below 10000vpm. Even in the heaviest low slump concrete loads. (Tested in near 0 slump concrete). This 10000 - 12000vpm range is essential for high-quality concrete. Direct drive units "scream" have short lives and usually drop below 10000vpm when the head is immersed in concrete. Learn More
    loading
  3. OZTEC Standard Duty Rebar Shaker System

    Starting At $1,733.00
    Turn Your Rebar Into an OZTEC Standard Duty Rebar Shaker System (For rebar up to 7/8 inch diameter in most applications). Eliminate the time and mess of lowering a concrete vibrator into a cell containing a rebar and filled with grout. The splashes caused by the withdrawal of the vibrator are slippery dangerous and time consuming to cleanup. The Rebar Shaker simply slipped over the top of the rebar vibrates and consolidates grout in 5 to 7 seconds. Tremendous savings in man-hours from filling and refilling cells clean-up and lost time due to injury from slips and falls are realized through the use of the Rebar Shaker. No human errors such as skipping cells and poor vibrating techniques (i.e. not letting vibrator touch the bottom or withdrawing to fast) which result in poor consolidation and a weak bond between the rebar and the grout. Learn More
    loading
  4. OZTEC Standard Duty Rebar Shaker Head H-RBS

    Starting At $786.00
    Turn Your Rebar Into A Vibrator with an OZTEC Standard Duty Rebar Shaker Head H-RBS (For rebar up to 7/8 inch diameter in most applications). Eliminate the time and mess of lowering a concrete vibrator into a cell containing a rebar and filled with grout. The splashes caused by the withdrawal of the vibrator are slippery dangerous and time consuming to cleanup. The Rebar Shaker simply slipped over the top of the rebar vibrates and consolidates grout in 5 to 7 seconds. Tremendous savings in man-hours from filling and refilling cells clean-up and lost time due to injury from slips and falls are realized through the use of the Rebar Shaker. No human errors such as skipping cells and poor vibrating techniques (i.e. not letting vibrator touch the bottom or withdrawing to fast) which result in poor consolidation and a weak bond between the rebar and the grout. Learn More
    loading
  5. OZTEC 16ft Flexible Concrete Vibrator Shaft FS16-OZ

    Starting At $468.00
    The OZTEC 16ft Flexible Concrete Vibrator Shaft FS16-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  6. OZTEC GV-5WH 5 HP Gas Concrete Vibrator Power Unit

    Starting At $2,185.00
    The OZTEC GV-5WH 5 HP Gas Concrete Vibrator Power Unit Carry Handle and Wheelbarrow models with flexible shaft storage are ideal for any job site. Utilizing a Honda engine these power plants run all steel and rubber heads up to 2.75 inch diameter. Learn More
    loading
  7. OZTEC GV-5H 5 HP Gas Concrete Vibrator Power Unit

    Starting At $2,049.00
    The OZTEC GV-5H 5 HP Gas Concrete Vibrator Power Unit Carry Handle and Wheelbarrow models with flexible shaft storage are ideal for any job site. Utilizing a Honda engine these power plants run all steel and rubber heads up to 2.75 inch diameter. Learn More
    loading
  8. OZTEC BP-35 4-Stroke Gas Backpack Concrete Vibrator

    Starting At $1,814.00
    The OZTEC BP-35 4-Stroke Gas Backpack Concrete Vibrator is powerful portable and reliable. Oztec gas power units provide ultimate and immediate adaptability on the job. Utilizing rugged and dependable Honda gasoline engines coupled to our "speed-up" transmission vibrator heads develop 12000 vpm and never drop below 10000vpm. Even in the heaviest low slump concrete loads. (Tested in near 0 slump concrete). This 10000 - 12000vpm range is essential for high-quality concrete. Direct drive units "scream" have short lives and usually drop below 10000vpm when the head is immersed in concrete. Learn More
    loading
  9. OZTEC BP-50A 4-Stroke Gas Backpack Concrete Vibrator

    Starting At $2,586.00
    The OZTEC BP-50A 4-Stroke Gas Backpack Concrete Vibrator is powerful portable and reliable. Oztec gas power units provide ultimate and immediate adaptability on the job. Utilizing rugged and dependable Honda gasoline engines coupled to our "speed-up" transmission vibrator heads develop 12000 vpm and never drop below 10000vpm. Even in the heaviest low slump concrete loads. (Tested in near 0 slump concrete). This 10000 - 12000vpm range is essential for high-quality concrete. Direct drive units "scream" have short lives and usually drop below 10000vpm when the head is immersed in concrete. Learn More
    loading
  10. OZTEC CG12E Electric Concrete Ceiling Grinder

    Starting At $2,909.00
    The OZTEC CG12E Concrete Ceiling Grinder can smooth concrete ceilings from 7 to 12 high with this unique electric concrete grinder machine. Perfect for grinding/smoothing concrete ceilings in parking structures, hotels, and condos. Learn More
    loading
  11. OZTEC CG12E-DC-7-H Electric Concrete Ceiling Grinder

    Starting At $4,441.00
    The OZTEC CG12E-DC-7-H Electric Concrete Ceiling Grinder can smooth concrete ceilings from 7 to 12 high with this unique concrete ceiling grinder. Perfect for grinding/smoothing concrete ceilings in parking structures hotels and condos. Learn More
    loading
  12. OZTEC 1.8 HP Electric Concrete Vibrator 1.8-OZ

    Starting At $633.00
    The OZTEC 1.8 HP Electric Concrete Vibrator 1.8-OZ motors are manufactured to exacting specifications to withstand the rough day to day abuses associated with construction sites. Lightweight compact and fitted with our comfortable adjustable shoulder strap this one man power unit will speed through the stiffest concrete. Using the Vibrator Selection Chart allows you to combine power units with any of Oztec's steel or rubber vibrator heads for maximum productivity. Learn More
    loading
  13. OZTEC 2.4 HP Electric Concrete Vibrator 2.4-OZ

    Starting At $704.00
    The OZTEC 2.4 HP Electric Concrete Vibrators' 2.4-OZ motors are manufactured to exacting specifications to withstand the rough day to day abuses associated with construction sites. Lightweight compact and fitted with our comfortable adjustable shoulder strap this one man power unit will speed through the stiffest concrete. Using the Vibrator Selection Chart allows you to combine power units with any of Oztec's steel or rubber vibrator heads for maximum productivity. Learn More
    loading
  14. OZTEC 3.2 HP Electric Concrete Vibrator 3.2-OZ

    Starting At $910.00
    The OZTEC 3.2 HP Electric Concrete Vibrator 3.2-OZ motors are manufactured to exacting specifications to withstand the rough day to day abuses associated with construction sites. Lightweight compact and fitted with our comfortable adjustable shoulder strap, this one-man electric portable concrete vibrator power unit speed through the stiffest concrete. Using the Vibrator Selection Chart allows you to combine power units with any of Oztec's steel or rubber vibrator heads for maximum productivity. Learn More
    loading
  15. OZTEC CG12G Gas Concrete Ceiling Grinder

    Starting At $2,955.00
    The OZTEC CG12G Gas Powered Concrete Ceiling Grinder can smooth concrete ceilings from 7 to 12 high with this unique concrete ceiling grinder. Perfect for grinding/smoothing concrete ceilings in parking structures hotels and condos. Learn More
    loading
  16. OZTEC 2.75in Rubber Vibrator Head HR275-OZ

    Starting At $825.00
    Use the OZTEC 2.75in Rubber Vibrator Head HR275-OZ to vibrate concrete around rebar. Epoxy coated rebar presents a particularly troublesome problem. Steel heads act like an electric hammer striking any rebar or forms they contact over 10000 times per minute with a force from hundreds to over 2000 pounds per blow. Contact with a steel vibrator head of as little as one second can chip enough coating to subject the steel to deep rust. Oztec's patented High Efficiency Rubber Head vibrator head not only meets DOT non-metal head specifications for protecting coated rebar and expensive forms but exhibit some very special and unique properties. The High Efficiency Rubber Head urethane dimpled construction sends strong shock waves off the entire length of the head with a larger radius of action producing denser concrete with less voids to patch. Oztec's patented High Efficiency Rubber Head Will outperform any other type of vibrator round square hi-cycle etcAny Type! Learn More
    loading
  17. OZTEC 2.5in Rubber Vibrator Head HR250-OZ

    Starting At $627.00
    Use the OZTEC 2.5in Rubber Vibrator Head HR250-OZ to vibrate concrete around rebar. Epoxy coated rebar presents a particularly troublesome problem. Steel heads act like an electric hammer striking any rebar or forms they contact over 10000 times per minute with a force from hundreds to over 2000 pounds per blow. Contact with a steel vibrator head of as little as one second can chip enough coating to subject the steel to deep rust. Oztec's patented High Efficiency Rubber Head vibrator head not only meets DOT non-metal head specifications for protecting coated rebar and expensive forms but exhibit some very special and unique properties. The High Efficiency Rubber Head urethane dimpled construction sends strong shock waves off the entire length of the head with a larger radius of action producing denser concrete with less voids to patch. Oztec's patented High Efficiency Rubber Head Will outperform any other type of vibrator round square hi-cycle etcAny Type! Learn More
    loading
  18. OZTEC 1-7/8in Rubber Vibrator Head HR188-OZ

    Starting At $486.00
    Use the OZTEC 1-7/8in Rubber Vibrator Head HR188-OZ to vibrate concrete around rebar. Epoxy coated rebar presents a particularly troublesome problem. Steel heads act like an electric hammer striking any rebar or forms they contact over 10000 times per minute with a force from hundreds to over 2000 pounds per blow. Contact with a steel vibrator head of as little as one second can chip enough coating to subject the steel to deep rust. Oztec's patented High Efficiency Rubber Head vibrator head not only meets DOT non-metal head specifications for protecting coated rebar and expensive forms but exhibit some very special and unique properties. The High Efficiency Rubber Head urethane dimpled construction sends strong shock waves off the entire length of the head with a larger radius of action producing denser concrete with less voids to patch. Oztec's patented High Efficiency Rubber Head Will outperform any other type of vibrator round square hi-cycle etcAny Type! Learn More
    loading
  19. OZTEC 2.5in Steel Vibrator Head H250-OZ

    Starting At $461.00
    The OZTEC 2.5in Steel Vibrator Head H250-OZ the highest amplitude and centrifugal force generating the largest radius of influence of any heads available on the market. Energy is efficiently transferred from the motor via the shaft to the head which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of flexible shaftsThe results are exceptional! Superior consolidation increased productivity and a process more forgiving of less than perfect vibrating techniques. The benefits? Lower cost higher earnings and superior quality concrete! Learn More
    loading
  20. OZTEC 2in Steel Vibrator Head H200-OZ

    Starting At $390.00
    The OZTEC 2in Steel Vibrator Head H200-OZ the highest amplitude and centrifugal force generating the largest radius of influence of any heads available on the market. Energy is efficiently transferred from the motor via the shaft to the head which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of flexible shaftsThe results are exceptional! Superior consolidation increased productivity and a process more forgiving of less than perfect vibrating techniques. The benefits? Lower cost higher earnings and superior quality concrete! Learn More
    loading
  21. OZTEC 1.75in Steel Vibrator Head H175-OZ

    Starting At $353.00
    The OZTEC 1.75in Steel Vibrator Head H175-OZ the highest amplitude and centrifugal force generating the largest radius of influence of any heads available on the market. Energy is efficiently transferred from the motor via the shaft to the head which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of flexible shaftsThe results are exceptional! Superior consolidation increased productivity and a process more forgiving of less than perfect vibrating techniques. The benefits? Lower cost higher earnings and superior quality concrete! Learn More
    loading
  22. OZTEC 14ft Flexible Concrete Vibrator Shaft FS14-OZ

    Starting At $364.00
    The OZTEC 14ft Flexible Concrete Vibrator Shaft FS14-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  23. OZTEC 21ft Flexible Concrete Vibrator Shaft FS21-OZ

    Starting At $476.00
    The OZTEC 21ft Flexible Concrete Vibrator Shaft FS21-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  24. OZTEC 2ft Flexible Concrete Vibrator Shaft FS02-OZ

    Starting At $120.00
    The OZTEC 2ft Flexible Concrete Vibrator Shaft FS02-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  25. OZTEC 5ft Flexible Rebar Shaker Shaft FS-RBS-05

    Starting At $308.00
    The OZTEC 5ft Flexible Rebar Shaker Shaft FS-RBS-05 transmits power from the power source to the rebar shaker head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units. Learn More
    loading
  26. OZTEC 5ft Flexible Concrete Vibrator Shaft FS05-OZ

    Starting At $173.00
    The OZTEC 5ft Flexible Concrete Vibrator Shaft FS05-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  27. OZTEC 7ft Flexible Concrete Vibrator Shaft FS07-OZ

    Starting At $216.00
    The OZTEC 7ft Flexible Concrete Vibrator Shaft FS07-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  28. OZTEC 10ft Flexible Concrete Vibrator Shaft FS10-OZ

    Starting At $278.00
    The OZTEC 10ft Flexible Concrete Vibrator Shaft FS10-OZ transmits power from the power source to the vibrating head with one of Oztec's flexible shafts. Oztec Flexible Shaft inner cores are made from extra-high carbon steel wires with casings made from tough abrasion resistant neoprene rubber reinforced with multiple layers of high tensile wire braiding with a hardened flat steel liner. This construction makes Oztec Flexible Shafts rigid enough for driving into the stiffest concrete without kinking yet limber and non-slip for easy and effective handling. Oztec Flexible Shafts are interchangeable on all Oztec power units are reversible (doubling their service life) and come supplied with quick change adapters. Standard lengths (in feet): 2 5 7 10 12 14 16 18 and 21. Oztec Flexible Shafts can be coupled to 42 feet using shaft coupling #6725A1. Custom lengths are available. Orbiting action rotates concrete (about 30 rpm) and packs concrete between the rebar and the form. Learn More
    loading
  29. OZTEC 1in Steel Vibrator Head H100-OZ

    Starting At $197.00
    The OZTEC 1in Steel Vibrator Head H100-OZ produces the highest amplitude and centrifugal force generating the largest radius of influence of any heads available on the market. Energy is efficiently transferred from the motor via the shaft to the head which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of flexible shaftsThe results are exceptional! Superior consolidation increased productivity and a process more forgiving of less than perfect vibrating techniques. The benefits? Lower cost higher earnings and superior quality concrete! Learn More
    loading
  30. OZTEC 1.25in Steel Vibrator Head H125-OZ

    Starting At $301.00
    The OZTEC 1.25in Steel Vibrator Head H125-OZ the highest amplitude and centrifugal force generating the largest radius of influence of any heads available on the market. Energy is efficiently transferred from the motor via the shaft to the head which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of flexible shaftsThe results are exceptional! Superior consolidation increased productivity and a process more forgiving of less than perfect vibrating techniques. The benefits? Lower cost higher earnings and superior quality concrete! Learn More
    loading
Popularity
Set Descending Direction

Grid List

30 per page

Items 1 to 30 of 31 total

Page:
  1. 1
  2. 2

Oztec Concrete Vibrators